Author Topic: Pickups ?????????????????????????????????????????????? (Read 432 times)

germansal · « **on:** June 06, 2009, 06:58:29 PM »

hi i have a problem ,i need to replace my bridge pickup and i would like to know the price
somebody can help me???''''''''''''

jazzyvee · « **Reply #1 on:** June 07, 2009, 12:50:38 AM »

Guitar or bass?

germansal · « **Reply #2 on:** June 07, 2009, 01:58:50 AM »

germansal · « **Reply #3 on:** June 07, 2009, 02:14:47 AM »

oh sorry?

?,BASS

keith_h · « **Reply #4 on:** June 07, 2009, 06:20:38 AM »

You should contact Alembic directly via e-mail or telephone (fastest method) to get a quote for a new pickup and shipping.

Keith

serialnumber12 · « **Reply #5 on:** June 07, 2009, 06:50:57 AM »

it might not be the pickup at all....what are you experiencing?

germansal · « **Reply #6 on:** June 07, 2009, 08:17:28 AM »

My bass tech here in Spain told me :the bridge position pickup its dead

terryc · « **Reply #7 on:** June 07, 2009, 11:39:11 AM »

Okay germansal before you do anything at all we all need to know:-
What bass have you got
What are the actual problems you have

Without dissing your guitar tech sometimes it maybe a very minor fault. Alembic pick ups are encased in epoxy and are just about indestructible in normal use..I think I have heard of only one case of a pick up going bad.
there are many variables such as
Are the pots touching the conductive paint
Has the connector broke
Are the pre amps working
Is the battery new
All of us here at the forum have a vast amount of imformation and if all else fails then call Alembic!

germansal · « **Reply #8 on:** June 07, 2009, 11:57:34 AM »

MY BASS IS AN SERIES 1 1979 4 STRINGS
MY BASS TECH HERE IN SPAIN TOLD ME THAT THERE S A PROBLEM INSIDE THE PICKUP,AND HE ALSO TOLD ME ABOUT THE EPOXY STUFF
ALL THIS NIGTHMARE STARTED WITH THE PICK MAKING A TERRIFIC NOISE
SO RIGTH NOW I,M USING ONLY THE NECK PICKUP

serialnumber12 · « **Reply #9 on:** June 07, 2009, 12:05:06 PM »

do you have the power supply & cable?....the jacks on alembics in the late 70's are mono that's why you only have the front pickup, both pickups will work with the 5 pin cable & power supply with a standard 1/4 plug.

(Message edited by serialnumber12 on June 07, 2009)

lbpesq · « **Reply #10 on:** June 07, 2009, 01:27:11 PM »

One thing you can try is to swap the wiring on the two pickups and see if the problem stays with the same pickup (bad pickup) or changes to the other pickup (problem is not the pickup).

Bill, tgo

terryc · « **Reply #11 on:** June 08, 2009, 01:43:22 AM »

Sounds like the pick up has gone microphonic but this very rare.
I would try everyone's suggestions, sorry I cannot offer more but I own a mono Signature bass and have no experience of SI & II basses with their associated power supply & cables

funkyjazzjunky · « **Reply #12 on:** June 08, 2009, 02:30:49 PM »

Contact the sites moderator Dave Houck.

He is not a technical wizard, but he will know who to contact and/or show you a solution from a previous post.

musashi · « **Reply #13 on:** June 09, 2009, 03:45:23 AM »

I'm thinking serialnumber12 may have hit it on the head... Are you running through the power supply or running off the 1/4 inch jack? Other than a friend trying to lower the neck pick-up for ease of slapping on a 70's Series I and having it break in the middle, I'm not aware of the failure of any Alembic pick-up.

Plugging in a 1/4 inch cable on an older Series bass will render the bridge pick-up inoperable...

(Message edited by musashi on June 09, 2009)

germansal · « **Reply #14 on:** June 09, 2009, 06:42:19 AM »

what do you mean???''''''
i got to run the bass trough power supply?always?