Author Topic: Mxy pickups  (Read 968 times)

90k6259

  • Member
  • ***
  • Posts: 82
Mxy pickups
« on: July 08, 2005, 08:12:00 PM »
IF anyone is interested there is a set of mxy pickups out of a 1992 essence four string on ebay

David Houck

  • Global Moderator
  • Senior Member
  • ******
  • Posts: 15595
Mxy pickups
« Reply #1 on: July 08, 2005, 09:16:07 PM »
I was thinking that someone around here was looking for a set just recently; so I went and looked in the Wanted section - and it was you!

90k6259

  • Member
  • ***
  • Posts: 82
Mxy pickups
« Reply #2 on: July 09, 2005, 09:18:27 AM »
Yes Dave . However they didn't fit my 90 Essence.  There was a change in the design of the pickup mold by 92.

David Houck

  • Global Moderator
  • Senior Member
  • ******
  • Posts: 15595
Mxy pickups
« Reply #3 on: July 09, 2005, 09:11:15 PM »
Oh yes, I remember your post and Mica's response!  I have an S1 that has a similar problem.  A previous owner had Alembic install new pickups; and because the holes on the new pickups are not in the same position as the originals, the adjusting screws do not line up properly.

bob

  • club
  • Senior Member
  • *
  • Posts: 808
Mxy pickups
« Reply #4 on: July 09, 2005, 11:21:44 PM »
Perhaps another FAQ candidate? Not just the MXY, but also Series (and maybe others)?

David Houck

  • Global Moderator
  • Senior Member
  • ******
  • Posts: 15595
Mxy pickups
« Reply #5 on: July 10, 2005, 07:55:11 AM »
Bob, how would it read?  I have no idea when the screw hole pattern changed for the different housings; and considering Mica's response, I'm guessing she doesn't know either.  There probably isn't a record.  I suppose we could just simply say something like due to a change in the pattern at some unknown point in time, older and newer pickups are not necessarily completely interchangable.  What do you think?  On mine, it is a bit of a problem.  Maybe at some point I'll send it back to Santa Rosa and have them look at it.

richbass939

  • club
  • Senior Member
  • *
  • Posts: 1221
Mxy pickups
« Reply #6 on: July 10, 2005, 09:12:36 AM »
I have 2 Epics (MXY pickups) that have different hole spacings.  The '95 4 string has holes more toward the edges.  The '98 5 string has holes more toward the middle.
Rich

David Houck

  • Global Moderator
  • Senior Member
  • ******
  • Posts: 15595
Mxy pickups
« Reply #7 on: July 10, 2005, 10:24:12 AM »
I wonder if that narrows down the time frame when the spacings were changed; or whether it indicates that the spacings may be variable over time.

90k6259

  • Member
  • ***
  • Posts: 82
Mxy pickups
« Reply #8 on: July 10, 2005, 03:35:14 PM »
MY Apologies to all.I made an assumption in my listing  that Alembic would know the date of the mold change.I Assumed Alembic keeped track of these things, Even though Mica may not have had the information at her fingertips.
For this reason I have ended the listing. My intention is not to be misleading. I'm just some guy  trying to fix his Alembic.
 
(Message edited by 90k6259 on July 10, 2005)

bob

  • club
  • Senior Member
  • *
  • Posts: 808
Mxy pickups
« Reply #9 on: July 10, 2005, 10:19:47 PM »
We should try to figure this out.
 
Rich and Roy both seem to have some useful numbers. Let's assume that the width of the MXY (along the length of the strings) has not changed, and that only the hole spacing has changed, but has always been centered.
 
So we list the latest instrument serial number and date of birth, that has the wide spacing, as well as the earliest with the narrow spacing, and of course say what the wide and narrow spacing is (center-to-center hole spacing, inches or mm, your choice).
 
Anyone who has conflicting evidence, or can help narrow down the time range, posts that information (maybe we should continue here, since people can't respond to the FAQ section).
 
It seems like a pretty safe bet that the mold didn't change very often, so maybe we can pin it down pretty closely, and at least let people know what the measurements are.
 
The Series pickups have been around a lot longer, and perhaps there are more variations, but maybe we could start with Dave's and work backward or something.
 
And perhaps along the way, we can turn up a set of pickups for Roy.

jorge_s

  • club
  • Member
  • *
  • Posts: 182
Mxy pickups
« Reply #10 on: July 11, 2005, 06:01:12 AM »
Roy, please e-mail me.  I'd be interested in buying those pickups.  I was watching the auction with the intention to bid but then it ended.  Please let me know if you still want to sell them.

David Houck

  • Global Moderator
  • Senior Member
  • ******
  • Posts: 15595
Mxy pickups
« Reply #11 on: July 11, 2005, 06:58:17 AM »
Bob; so that we don't interfere with the discussion of the pickups that are for sale in this thread, let's move the discussion about the measurements ... here.  I've linked back to this thread so that others can read what's been discussed so far.

90k6259

  • Member
  • ***
  • Posts: 82
Mxy pickups
« Reply #12 on: July 11, 2005, 04:50:59 PM »
Dave; as you can evidenly see buy my actions the damage has already been done. Now if you said you were moving the tread to avoid further damage than that would make sense.

David Houck

  • Global Moderator
  • Senior Member
  • ******
  • Posts: 15595
Mxy pickups
« Reply #13 on: July 11, 2005, 07:38:14 PM »
Hi Roy;
 
As Jorge had just posted a message to this thread indicating an interest in your pickups, I thought it would be best to move the discussion about measurements to a new thread.  It seemed to me to be a sensible thing to do.

90k6259

  • Member
  • ***
  • Posts: 82
Mxy pickups
« Reply #14 on: July 11, 2005, 08:22:42 PM »
Hi Dave;
 
Obviously you are missing my point. I will continue the conversation via E-mail